| 物品名称 | 规格型号 | 数量 | 单位 | 描述 |
| 倾翻臂液压缸 | PNXLY | 2.00 | 个 | {"规格型号":"PNXLY","图号":"无","材质":"碳钢,活塞杆,缸筒表面镀铬","压力":"20MPa","行程":"762mm","活塞杆直径":"45mm","活塞直径":"63.5mm","密封件材质":"氟橡胶,丁腈橡胶,聚四氟乙烯","接口尺寸":"活塞杆螺纹1-7/8-12","所属设备名称":"铸造机","设备型号":"800S","设备生产厂家":"美国瓦格斯塔夫","国产/进口":"进口","使用寿命":"730天","特殊要求":"介质:液压油","参照标准":"JB/T 10205-2010","备注":"缸径152.4mm,最小缩回长度1254mm.验收:到货不合格供应商必须无条件退货或换货处理,所产生的费用由供货方承担."} |
| 液压缸 | ZSG100*2300 | 2.00 | 个 | {"规格型号":"ZSG100*2300","图号":"无","材质":"缸筒,活塞,活塞杆,阀块为45#钢,表面镀铬","压力":"10MPa","行程":"2300mm","活塞杆直径":"100mm","活塞直径":"115mm","密封件材质":"FPM/HPU","接口尺寸":"鱼眼轴承接口70mm","所属设备名称":"双室炉","设备型号":"90T","设备生产厂家":"德国LOI","国产/进口":"进口","使用寿命":"1825天","特殊要求":"缸筒外径150mm,内径115mm,适用温度约80℃","参照标准":"JB/T 10205-2010","备注":"液压缸带底部阀块,阀块接口尺寸:3/4英寸14牙*1;1/2英寸14牙*1.\n缸筒接口尺寸:1/4英寸19牙*2.\n验收标准:满足上述技术要求，使用无泄漏.不合格品处理标准:当到货物资与技术要求不符时,退换货处理."} |
| 取样剪升降液压缸 | Φ180/Φ125*1075mm | 1.00 | 件 | {"规格型号":"Φ180/Φ125*1075mm","图号":"无","材质":"活塞杆:42CrMo","压力":"200bar","行程":"1075mm","活塞杆直径":"125mm","活塞直径":"180mm","密封件材质":"氟橡胶","接口尺寸":"杆端连接尺寸1-1/4″,腔端连接尺寸1-1/4″","所属设备名称":"热精轧机","设备型号":"HC-HB-RZJ-02","设备生产厂家":"德国SMS","国产/进口":"进口设备","使用寿命":"730天","特殊要求":"无","参照标准":"GB/T 10205-2010","备注":"到货物资与技术要求不符时,换货处理."} |
| 液压缸 | 150/140-950 | 1.00 | 个 | {"规格型号":"150/140-950","材质":"45#钢","压力":"16MPa","行程":"950","活塞杆直径":"140mm","活塞直径":"150mm","密封件材质":"丁晴橡胶，聚四氟乙烯，聚氨酯","国产/进口":"进口","使用寿命":"1095天"} |
| 液压缸 | 160/110-4250 | 1.00 | 个 | {"规格型号":"160/110-4250","图号":"无","材质":"45钢","压力":"16MPa","行程":"4250mm","活塞杆直径":"110mm","活塞直径":"160mm","密封件材质":"丁腈橡胶、聚氨酯、聚四氟乙烯","接口尺寸":"G1","所属设备名称":"2号包装线","设备型号":"SLZ0500295","设备生产厂家":"德国西马克","国产/进口":"国产","使用寿命":"730天","特殊要求":"活塞杆材质:45#钢调质,表面镀铬.前后节流缓冲,缸头螺纹M80*3,缸头鱼眼轴承孔内径100mm","参照标准":"GB/T 15622-2023","备注":"到货拆封检查,表面无划伤,无磕碰,附带测试报告及合格证.若到货与技术要求不符,供货商无条件进行退换货处理.期间产生的一切费用由供货商负责."} |
| 液压缸 | 06M0241-CK-9-160/110 | 1.00 | 个 | {"规格型号":"06M0241-CK-9-160/110-4250-L301-AW-30-XV=1900","材质":"45钢","压力":"16MPa","行程":"4250mm","活塞杆直径":"110mm","活塞直径":"160mm","密封件材质":"丁腈橡胶、聚氨酯、聚四氟乙烯","使用寿命":"730天","特殊要求":"前部和后部快速可调式缓冲器，带前排气口和后排气口"} |
| 液压缸 | 80/50*40 | 4.00 | 个 | {"规格型号":"80/50*40","图号":"031011CBD182","材质":"45#钢，活塞杆表面镀铬","压力":"250bar","行程":"40mm","活塞杆直径":"50mm","活塞直径":"80mm","密封件材质":"聚四氟乙烯，丁腈橡胶","接口尺寸":"M100*2","所属设备名称":"铝箔轧机","设备型号":"φ280/850*2000","设备生产厂家":"德国阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"此缸体上无进、出油口，液压缸安装在底座内部。","参照标准":"JB/T 10205-2010","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 液压缸 | 80/50*47 | 4.00 | 个 | {"规格型号":"80/50*47","图号":"031011CBD183","材质":"45#钢，活塞杆表面镀铬","压力":"250bar","行程":"47mm","活塞杆直径":"50mm","活塞直径":"80mm","密封件材质":"聚四氟乙烯，丁腈橡胶","接口尺寸":"M100*2","所属设备名称":"铝箔轧机","设备型号":"φ280/850*2000","设备生产厂家":"德国阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"此缸体上无进、出油口，液压缸安装在底座内部。","参照标准":"JB/T 10205-2010","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 液压缸 | 80/50*30 | 4.00 | 个 | {"规格型号":"80/50*30","图号":"031011CBD184","材质":"45#钢，活塞杆表面镀铬","压力":"250bar","行程":"30mm","活塞杆直径":"50mm","活塞直径":"80mm","密封件材质":"聚四氟乙烯，丁腈橡胶","接口尺寸":"M100*2","所属设备名称":"铝箔轧机","设备型号":"φ280/850*2000","设备生产厂家":"德国阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"此缸体上无进、出油口，液压缸安装在底座内部。","参照标准":"JB/T 10205-2010","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 液压缸 | 80/50*25 | 4.00 | 个 | {"规格型号":"80/50*25","图号":"031011CBD185","材质":"45#钢，活塞杆表面镀铬","压力":"250bar","行程":"25mm","活塞杆直径":"50mm","活塞直径":"80mm","密封件材质":"聚四氟乙烯，丁腈橡胶","接口尺寸":"M100*2","所属设备名称":"铝箔轧机","设备型号":"φ280/850*2000","设备生产厂家":"德国阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"此缸体上无进、出油口，液压缸安装在底座内部。","参照标准":"JB/T 10205-2010","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 气缸 | 50/20*55 | 20.00 | 个 | {"型号":"50/20*55","规格尺寸":"活塞直径/活塞杆直径*行程= 50/20*55mm,接口尺寸G1/4","工作方式":"单杆双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"空气","适用设备":"铝箔轧机","国内/国外":"国内","生产厂家":"无要求","参照标准":"GB/T 28781-2012","备注":"缸体材质;铝合金,活塞杆材质;45#钢表面镀铬.两端带缓冲可调节,附带检测磁环.使用寿命;365天.到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 气缸 | RA8160M650D | 4.00 | 个 | {"型号":"RA8160M650D","规格尺寸":"160*650mm","工作方式":"双作用气缸","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"阿亨巴赫轧机","国内/国外":"国外","生产厂家":"诺冠","参照标准":"GB/T 23252-2009","备注":"验收：到货尺寸必须满足技术要求，对于不合格的进行退换货处理，所有产生费用由卖家承担。"} |
| 气缸 | 63/20*220 | 4.00 | 个 | {"型号":"63/20*220","规格尺寸":"行程:220mm;接口尺寸:G3/8;缸径:63mm;杆径;20mm","工作方式":"单杆双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"空气","适用设备":"铝箔轧机","国内/国外":"国内","生产厂家":"无","参照标准":"GB/T 28781-2012","备注":"驱动方式;两端缓冲可调,侧向气口,缸体材质;铝合金,活塞杆材质;45#钢表面镀铬.使用寿命;365天.到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
